WARNING — This software is not an emergency stop. Your machine must have a hardwired E-stop that removes motor and spindle power. Keep it within reach whenever the machine is powered.

v0.5.19 · 7dcbf26f8d80 · 2026-11-12 14:20
SynthetosRunrun.synthetos.com · machine control

run.synthetos.com · Wiring

Wiring diagram

Draw how your machine is wired to the board. Every rule cites its source. This page never talks to a machine, and it does not replace a qualified electrician.

TinyG v6 and v7 have no connector data yet, so they have no diagram.

Parts

No parts yet.

Connect

Connections
WireFromToShieldedActions

INCOMPLETE — NO E-STOP SHOWN

Findings (1)

  • E-STOP WR-ESTOP No E-stop is shown. Exports carry the "INCOMPLETE — NO E-STOP SHOWN" watermark and "wired per diagram" cannot be attested. Source: SAFETY W14; TOOLS_PLAN §6.5 E-STOP rule

Expected settings (advisory)

Each key is accepted on its own into the settings draft. Nothing is written to a machine here.

  • xsn = 0 nothing on Xmin (J7.3): off Source: EN canonical_machine.c:3174-3175 ([0=off,1=homing,2=limit,3=limit+homing,4=probe])
  • xsx = 0 nothing on Xmax (J7.4): off Source: EN canonical_machine.c:3174-3175 ([0=off,1=homing,2=limit,3=limit+homing,4=probe])
  • ysn = 0 nothing on Ymin (J7.5): off Source: EN canonical_machine.c:3174-3175 ([0=off,1=homing,2=limit,3=limit+homing,4=probe])
  • ysx = 0 nothing on Ymax (J7.6): off Source: EN canonical_machine.c:3174-3175 ([0=off,1=homing,2=limit,3=limit+homing,4=probe])
  • zsn = 0 nothing on Zmin (J8.3): off Source: EN canonical_machine.c:3174-3175 ([0=off,1=homing,2=limit,3=limit+homing,4=probe])
  • zsx = 0 nothing on Zmax (J8.4): off Source: EN canonical_machine.c:3174-3175 ([0=off,1=homing,2=limit,3=limit+homing,4=probe])
  • asn = 0 nothing on Amin (J8.5): off Source: EN canonical_machine.c:3174-3175 ([0=off,1=homing,2=limit,3=limit+homing,4=probe])
  • asx = 0 nothing on Amax (J8.6): off Source: EN canonical_machine.c:3174-3175 ([0=off,1=homing,2=limit,3=limit+homing,4=probe])

Settings draft: empty

Export and checklist

  1. Switch off and unplug every supply before wiring. Keep power off until the last step. Source: TOOLS_PLAN §6.5 checklist
  2. Check the polarity and voltage of every supply with a meter before connecting it to the board. Source: TOOLS_PLAN §6.5 checklist
  3. Connect or disconnect motors only with power off: power off, connect the motors, then power on. Never plug or unplug a motor with power on. Source: SAFETY C6 note; CIT-3
  4. Wire the motor phases by the labels printed on the board; the diagram follows the board print. Source: TOOLS_PLAN §6.5 (TinyG v8 phase order not verified)
  5. Turn the current trimpots only within their range: about 8 o’clock to about 4 o’clock (270 degrees). Never force them past the stops. Source: TinyG.wiki TinyG-Tuning.md:23; Connecting-TinyG.md:144
  6. Check every connection against the wire table, then power on. Source: TOOLS_PLAN §6.5 checklist

Not available: no E-stop that removes motor and spindle power is shown.